Sanyo C4272R S/C Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Split-systém klimatizace Sanyo C4272R S/C. Sanyo C4272R S/C User's Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 111
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
X
K
T
U
C
RC
(WD)
RC
(WL)
TRC
SC
85464359863005 ©SANYO 2007
– Split System Heat Pump Air Conditioner –
INSTALLATION INSTRUCTIONS
Model Combinations
Combine indoor and outdoor units only as listed below.
Indoor Units and Outdoor Units
* When air discharge chamber is installed.
OPERATING LIMITS
Maximum Conditions Cooling / Heating
Outdoor temperature : 109°F DB / 65°F WB
Room temperature : 71°F WB / 80°F DB
Minimum Conditions
Outdoor temperature : 0°F* DB / 5°F WB
Room temperature : 57°F WB / 59°F DB
Units should be installed by licensed contractor according to
local code requirements.
Indoor Unit Type 26 30 36 42 Remarks
X
4-Way Air Discharge
XH2672R XH3672R XH4272R Optional remote controller
Semi-Concealed
XHW2672R XHW3672R XHW4272R with Wired Remote Controller: RCS-TM80BG
KH2672R KH3072R KH3672R Optional remote controller
K Wall-Mounted
KHS2672R KHS3072R KHS3672R with Wireless Remote Controller: RCS-SH1UA
KHH2672R Optional remote controller
KHHS2672R
with Wireless Remote Controller: RCS-SH1UA
TH2672R TH3672R TH4272R Optional remote controller
THW2672R THW3672R THW4272R with Wired Remote Controller: RCS-TM80BG
T Ceiling-Mounted THH2672R THH3672R Unit with Back-up heater
THHW2672R THHW3672R
Unit with Back-up heater
with Wired Remote Controller: RCS-TM80BG
U Concealed-Duct
UH2672R UH3672R Optional remote controller
UHW2672R UHW3672R with Wired Remote Controller: RCS-TM80BG
C Outdoor Units
CH2672R CH3072R CH3672R CH4272R H/P
C2672R C3072R C3672R C4272R S/C
RC
Wired Remote
RCS-SH80UG (Optional part)
(WD)
Controller
RC Wireless Remote
Built-in type: RCS-SH80UA.WL (Optional part) for X and T type Indoor units
(WL)
Controller
External type: RCS-BH80UA.WL (Optional part) for U type Indoor units
Built-in type: RCS-SH80UA (Accessory part / Optional part) for K type Indoor units
Timer Remote
for X, T and U type Indoor units.
TRC
Controller
RCS-TM80BG* (Accessory part / Optional part)
* Timer Remote Controller comes with
Owner’s Manual and Installation Instructions.
SC System Controller SHA-KC64UG (Optional part)
SANYO Commercial Solutions In Canada
A division of SANYO North America Corporation SANYO Canada Inc.
Cornerstone Business Park 1-300 Applewood Crescent
1062 Thorndale Avenue Concord, Ontario
Bensenville, IL 60106, U.S.A. L4K 5C7, Canada
07-115 SSHP_II 5/7/07 3:59 PM Page a
Zobrazit stránku 0
1 2 3 4 5 6 ... 110 111

Shrnutí obsahu

Strany 1 - INSTALLATION INSTRUCTIONS

XKTUCRC(WD)RC(WL)TRCSC85464359863005 ©SANYO 2007– Split System Heat Pump Air Conditioner –INSTALLATION INSTRUCTIONSModel CombinationsCombine indoor

Strany 2 - Please Read Before Starting

Special washer4Drain insulator 1Flare insulator1 SetDrain hose adaptor 1Drain hose clamp 4Insulating tape21Vinyl clamp 2Full-scale installation1diagra

Strany 3 - Check of Density Limit

100Fig. 9-12Fig. 9-139-4. Taping the Tubes(1) At this time, the refrigerant tubes (and electricalwiring if local codes permit) should be tapedtogethe

Strany 4 - Vacuum pump

OutletInletVacuum pumpManifold valvePressuregaugeLo HiCharge hoseOutdoor unitLiquidtubeGastubeNitrogen gas cylinder(In vertical standingposition)Close

Strany 5

C102Fig. 10-4(3) Pressurize the system up to 4.15 MPa (42 kgf/cm2G) with dry nitrogen gas and close the cylinder valve when the gauge reading reaches4

Strany 6 - CONTENTS

CFig. 10-5Fig. 10-610-3. Charging Additional Refrigerant Charging additional refrigerant (calculated from theliquid tube length as shown on page 14,

Strany 7

10411. TEST RUN11-1. Preparing for Test Run Before attempting to start the air conditioner,check the following:(1) All loose matter is removed from

Strany 8 - 1. GENERAL

105 X, T, U, K Type11-2. Caution This unit may be used in a single-type refrigerant system where 1 outdoor unit is connected to 1 indoorunit. The i

Strany 9

10611-4. Items to Check Before the Test Run(1) Turn the breaker ON at least 12 hours in advance in order to energize the crank case heater.(2) Fully

Strany 10 - (heat-resisting)

107Wired remote controller displayCauseCorrectionNothing is displayedNothing is displayedE 0 1 displayedE 0 2 displayedE 0 9 displayedE 1 4 displayedE

Strany 11 - Heating preparations

10811-8. Examples of Wiring Diagrams11-8-1. Basic wiring diagram 1Single-type system Be careful to avoid miswiring when connecting the wires. (Miswi

Strany 12

10911-8-2. Basic wiring diagram 2Group control (when a central control device is not used) Simultaneous-operation multi system A maximum of 8 indoor

Strany 13

11Table 1-5 (Accessories for the Wired Remote Controller)Part Name Figure‘Q’tyPart Name Figure‘Q’ty1 Spacers 22 Wire joints 4Wood screws 2Wired remot

Strany 14

11-8-3. Setting the outdoor unit system addressesFor basic wiring diagram 2 (Set the system addresses: 1, 2, 3...)ON120System address rotary switch(Se

Strany 15 - Min. indoor volume

11111-8-5. Indicating (marking) the indoor and outdoor unit combination number Indicate (mark) the number after automatic address setting is complete

Strany 16 - Ceiling-Mounted Type

12Table 1-7 (Accessories for the Timer Remote Controller)Part Name Figure‘Q’tyPart Name Figure‘Q’tyTimer Remote Controller1 Spacers 21Wood screws2 Cl

Strany 17

131-5. Tubing SizeSingle type Refrigerant tubing between the indoor and outdoor unitsshould be kept as short as possible. The length of the refrige

Strany 18

14Limit of elevationdifference betweenthe 2 unitsNo additional charge of compressor oil is necessary.*1If total tubing length becomes 100 to 165 ft.,

Strany 19 - 6-ø15/64 hole

15CAUTIONCAUTIONWARNING1. This unit requires no additional refrig-erant charge up to 100 ft. tubing length.In case of more than 100 ft., additionalref

Strany 20 - 4272R unit with STK-DRE140A

162. SELECTING THE INSTALLATION SITE2-1. Indoor UnitAVOID: areas where leakage of flammable gas may beexpected. places where large amounts of oil

Strany 21

2-2. Outdoor UnitAVOID: heat sources, exhaust fans, etc. (Fig. 2-1) damp, humid or uneven locationsDO: choose a place as cool as possible. choose

Strany 22 - STK-BDR140U for 4272R unit

18Fig. 2-5Fig. 2-6Fig. 2-72-3. Air-Discharge Chamber for Top DischargeBe sure to install an air discharge chamber in thefield when: it is difficult

Strany 23 - 4272R unit with STK-BDR140U

2-6. Dimensions of Wind DuctingReference diagram for air-discharge chamber (field supply)12(25/32)(25/32)(25/32)(25/32)21-13/169-27/3222-7/1623-15/32

Strany 24

2IMPORTANT! Please Read Before StartingThis air conditioning system meets strict safety and operatingstandards. As the installer or service person, it

Strany 25

Dimensions of Outdoor Unit with air-discharge chamber (field supply)2672R / 3072R / 3672R unit with STK-DRV80U13-3/82-17/3221-13/161/26-11/1625-31/324

Strany 26

21Reference diagram for air-discharge chamber (field supply)C(H)2672R / 3072R / 3672R / 4272R with STK-DRV80U & DRE140ARequired space around outdo

Strany 27 - Full-scale installation

2217-15/3225-13/329-3/1628-13/1615-9/3247-19/322311-7/83-31/329-3/1628-13/161-13/1647-19/3230-3/32145-29/3217-23/3219-11/1625-3213-5/1619-11/161-5/8 2

Strany 28 - Drain insulator (supplied)

2311-29/3228-13/16Wind directionWind directionWind directionWind directionWind directionWind direction48-7/1647-19/373724-7/815-15/1614-31/32 13/3219/

Strany 29 - Tube cover

Reference diagram for snow-proof vents – 1Space requirements for setting – (1)C(H)2672R / 3072R / 3672R / 4272R with STK-BDRE80A & STK-BDR140UMin.

Strany 30 - Air filter

25Reference diagram for snow-proof vents – 2Space requirements for setting – (2)C(H)2672R / 3072R / 3672R / 4272R with STK-BDRE80A & STK-BDR140UMi

Strany 31

X263. HOW TO INSTALL THE INDOOR UNIT 4-Way Air Discharge Semi-Concealed Type(X Type)3-1. Suspending the Indoor UnitThis unit uses a drain pump. Use

Strany 32 - For fresh air intake

27X3-3. Placing the Unit Inside the Ceiling(1) When placing the unit inside the ceiling, determinethe pitch of the suspension bolts using the supplie

Strany 33 - Fig. 3-18

X283-4. Installing the Drain Piping(1) Prepare standard hard PVC pipe for the drain anduse the supplied drain hose and hose band to pre-vent water le

Strany 34 - KH(S)2672R

29X3-5. Checking the DrainageAfter wiring and piping are completed, use the follow-ing procedure to check that the water will drain smooth-ly. For th

Strany 35 - KH(S)3072R, KH(S)3672R

2. The standards for minimum room volume are asfollows.(1) No partition (shaded portion)(2) When there is an effective opening with the adja-cent room

Strany 36 - KHH(S)2672R

X30 Ceiling Panel3-6. Before Installing the Ceiling Panel(1) Remove the air-intake grille and air filter from theceiling panel. (Figs. 3-13 and 3-14)

Strany 37 - Wall fixture

31X3-7. Installing the Ceiling Panel(1) Lift the ceiling panel and position it to align thepanel hook with the panel catch of the indoor unit.The cei

Strany 38 - Rawl plug

X323-9. Duct for Fresh AirThere is a duct connection part on side of the indoorunit. (Fig. 3-16)An optional air-intake plenum (including duct conne

Strany 39

33X(d) Installing the ceiling panelAttach the ceiling panel to the chamber. Drawing thepanel downwards sets the panel in position temporarilywith the

Strany 40

34K Wall-Mounted Type (K Type)3-10. Removing the Wall Fixture from the UnitRemove and discard the set screws and take off therear panel. (Fig. 3-19)

Strany 41

35KOne hole is required for the air conditioner tubing, andmay be either on the left or right side. (Also see section3-14. Preparing the Indoor Side T

Strany 42 - Right tubing

36KRemove and discard the set screws and take off thewall fixture. (Fig. 3-29)(1) Tape the full-scale installation diagram on the wallat the location

Strany 43 - Cover plate

37K3-12. Installing the Rear Panel on the WallBe sure to confirm that the wall is strong enough to suspendthe unit.See either Item a) or b) below dep

Strany 44

38KConfirm that the wall is strong enough to support theunit.a) If Wooden Wall(1) Attach the wall fixture to the wall with the 9 screwsprovided. (Fig.

Strany 45

39K3-13. Remove the Grille to Install the Indoor UnitBasically, these models can be installed and wired without removing the grille. If access to any

Strany 46 - (field supply)

4R407C tools Item compatible Remarkswith R410A?Manifold gauge Yes No Types of refrigerant, refrigerating machine oil, and pressure gauge are diff

Strany 47 - Ceiling support

40KHow to Remove the Grille(1) Remove the plastic cover. (Fig. 3-42)(2) Remove the clamp for the wiring connector.(Fig. 3-43)(3) Disconnect the 2 wiri

Strany 48 - Side panel

41K3-14. Preparing the Indoor Side TubingArrangement of tubing by directions(a) Right tubingThe corner of the right frame needs to be cut bya hacksaw

Strany 49

42KTubing can be extended in 4 directions as shown inFig. 3-54.Arrangement for Left Tubing(a) Cut out the left tubing outlet. (Fig. 3-55)Arrangement f

Strany 50 - Cut this portion

43K3-16. Wiring Instructions for Inter-Unit Connections(1) Insert the inter-unit wiring (according to local electrical codes) into the through-the-wa

Strany 51 - Dimension

WallPlasticcoverRearpanelWiring5"WallWall fixtureConnector Wiring5"44K(1) Insert the inter-unit wiring (according to localcodes) into the th

Strany 52 - Hexagonal nut

K(1) Shape the refrigerant tubing so that it can easily go intothe wall hole. (Fig. 3-62)CAUTIONIf using a stepladder, be careful tokeep your balance

Strany 53

46K3-17. Shaping the Tubing(1) Shape the refrigerant tubing so that it can easily gointo the hole. (Fig. 3-69)(2) Push the wiring, refrigerant tubing

Strany 54 - Support pieces

47T Ceiling-Mounted Type (T Type)3-19. Suspending the Indoor Unit(1) Place the full-scale diagram (supplied) on the ceiling at the spot where you wa

Strany 55

48T(5) Before suspending the indoor unit, remove the 2screws on the latch of the air-intake grilles, openthe grilles, and remove them by pushing the c

Strany 56

49TCeilingsurface.xorppAhcni 1Suspension boltWasher(supplied)Nut(field supply)Fig. 3-82Fig. 3-83Fig. 3-84(7) Suspend the indoor unit as follows.(a) Mo

Strany 57 - 5. ELECTRICAL WIRING

53-2. Use R410A exclusive cylinder only. When charging with a refrigerant cylinder, use anelectronic scale for charging refrigerant. In thiscase, if

Strany 58 - Grounding line

50T3-20. Duct for Fresh AirThere is a duct connection port (knock-out hole) at theright-rear on the panel top of the indoor unit for drawingin fresh

Strany 59 - .ni 8/3 pirtS

51U Concealed-Duct Type (U Type)3-22. Required Minimum Space forInstallation and ServiceThis air conditioner is usually installed above the ceiling

Strany 60

52U3-23. Suspending the Indoor UnitDepending on the ceiling type:• Insert suspension bolts as shown in Fig. 3-93or• Use existing ceiling supports or

Strany 61

53UFig. 3-97 shows an example of installation.3-24. Installing the Drain Piping(1) Prepare standard hard PVC pipe for the drain anduse the supplied

Strany 62

54UCAUTION Do not install an air bleeder tube as this may causewater to spray from the drain pipe outlet. (Fig. 3-100) If it is necessary to increas

Strany 63

55U3-26. Increasing the Fan SpeedIf external static pressure is too great (due to longextension of ducts, for example), the air flow volumemay drop t

Strany 64

564. HOW TO INSTALL THE OUTDOOR UNIT4-1. Installing the Outdoor Unit Use concrete or a similar material to create the base, andensure good drainage

Strany 65 - 6-7. Trouble Diagnostics

575. ELECTRICAL WIRING5-1. General Precautions on Wiring(1) Before wiring, confirm the rated voltage of the unitas shown on its nameplate, then carr

Strany 66 - Possible cause of malfunction

585-3. Wiring System DiagramsBasic wiring diagram for standard controlU2U1L1L2U1U212G21WHTRemote controllerDAIndoorunitBL1L2Grounding lineBLK21Inter-

Strany 67

59WARNINGLoose wiring may cause the terminal to overheat or resultin unit malfunction. A fire hazard may also exist. Therefore, ensure that allwiring

Strany 68 - ACL button

6 Concealed-Duct Type (U Type) . . . . . . . . . . . . . . 513-22. Required Minimum Space for Installation andService3-23. Suspending the Indoor Uni

Strany 69 - Sensor button

60RC(WD)6-1. Installation Site Selection Install the remote controller at a height of between3–5 ft. above the floor. Do not install the remote con

Strany 70 - Operating

61RC(WD)(1) When you open the decorative cover, you will seetwo gaps under the remote controller. Insert a coininto these gaps and pry off the back ca

Strany 71 - Electrical component box

62RC(WD)6-3. Basic Wiring DiagramUse shielded wires for inter-unit control wiring andground the shield on both sides. (Fig. 6-5) Otherwise misoperati

Strany 72 - All OFF( ) for

63RC(WD)6-4. Wiring System Diagram for Group ControlThis diagram shows when several units (maximumof 8) are controlled by a remote controller (mainun

Strany 73 - (STANDBY

64RC(WD)6-5. Wiring System Diagram for Multiple RemoteControllers When Installing Multiple Remote ControllersThis multiple remote controller system

Strany 74

65RC(WD)6-7. Trouble Diagnostics (1) Contents of remote controller switch alarm displayRemote controller is detecting error signal from indoor unitE

Strany 75 - Wood screws (2)

66RC(WD)P09P01P10P03P04P05P15P19P20P22P26P29P31H01F01F02F10F04F06F07F08F12F29Ceiling panel connection failureIndoor protectionFan protective thermosta

Strany 76 - TEST RUN

67RC(WD)(2) LED Indicator Messages on Outdoor Control PCB Power ON sequence1. No communication from indoor units in system2. Communication received f

Strany 77 - FILTER lamp

68RC(WL)When using this air conditioner with the wireless remote controller it may sometimes beimpossible to change the operation modes while other in

Strany 78 - Shielded wire

69RC(WL)7-2. Room Temperature Sensor SettingThe room temperature sensors are built into the indoorunit and the wireless remote controller. Either of t

Strany 79 - Connection wiring

7<RCS-BH80UA.WL>7-12. Separate Type Signal Receiving Unit Installation7-13. Electrical Wiring7-14. Test Run Switch7-15. Misoperation Alarm Indic

Strany 80

X70<RCS-SH80UA.WL>4-Way Air Discharge Semi-concealed Type(X Type)7-5. Indicator Section InstallationRemove the ceiling panel and indicator cover

Strany 81

71TCover ACover APanelIndicator sectionSide panel Indicator sectionCover B(Not used when the indicator section is installed.)Air intake grilleRecessRe

Strany 82 - Indicator

72RC(WL)7-9. Electrical WiringConnection method(1) Connect W1 to the indoor PCB WL connector.(2) Connect W3 from the indicator section with W2from the

Strany 83

73RC(WL)7-11. Misoperation Alarm IndicatorsAlarm indicator lamps on the indoor unit indicate theerror cause if the air conditioner fails to operateupo

Strany 84

74RC(WL)<RCS-BH80UA.WL>If the signal receiving unitis installed near a rapid-start or inverter typefluorescent lamp (neitherone uses glow lamps)

Strany 85 - (OPTIONAL PART)

When using the signal receiving unit on a wall withthe front exposed, choose a wall surface that thesignal receiving unit can be mounted on.(1) Insert

Strany 86

76RC(WL)7-13. Electrical WiringBe sure to do the wiring correctly (incorrectwiring will damage theequipment).Recommended wire diameter and allowable l

Strany 87 - 8-3. Address Switch Setting

7-15. Misoperation Alarm IndicatorsA blinking lamp for other than the signal receiving unitfilter shows that a problem has occurred in the unit, somak

Strany 88

78RC(WL)7-16. Basic Wiring DiagramBe sure to do the wiring correctly (incorrect wiring will damage the equipment).CAUTIONUse shielded wires for inter-

Strany 89

79RC(WL)7-17. Wiring System Diagram for Group ControlThis diagram shows when several units (maximum of8) are controlled by a signal receiving unit (ma

Strany 90 - Indoor unit No

81. GENERALThis booklet briefly outlines where and how to installthe air conditioning system. Please read over theentire set of instructions for the

Strany 91

80RC(WL)7-18. Wiring System Diagram for Multiple Remote ControllersWhen installing multiple remote controllersThis multiple system is used for operati

Strany 92

81RC(WL)Sliding switch 1 Wireless remote controller transmitterVerify that sliding switch 1 is in the “K” position.<For 3072R, 3672R>S: Flap mod

Strany 93

82RC(WL)7-21. Preparing for the Test Run7-21-1. Changing the room temperature sensor7-21-2. Using the remote controller7-21-3. Test runRoom temperatur

Strany 94

7-22. PrecautionsRequest that the customer be present at the time the test run is performed. Explain the Operation Manual to the customer, and then ha

Strany 95

84RC(WL)7-23. When Setting Indoor Unit Control PCB Switch for Wall-Mounted Indoor UnitWhen using either the wired or wireless remote controller, refe

Strany 96 - Back up battery

SC858.HOW TO INSTALL THE SYSTEM CONTROLLER(OPTIONAL PART)Fig. 8-1SystemcontrollerSwitch box(with cover)M4 × 1-3/16 in.Screws (2)Flat-topScrewBack case

Strany 97 - 9. HOW TO PROCESS TUBING

SC868-2. Electrical WiringB1Indoor unit PCBCRV(CN91: WHT)2P terminal baseIndoor unitSystem controllerAccessary connectorWire joint connectionB2B3B4B5B

Strany 98

87SC8-3. Address Switch Setting1ONMain/sub selection switchOFF: System controller operates as main controller.ON: System controller operates as sub-co

Strany 99 - Packed valve

88SC1ONWeekly timer input switchesSystem controller operation can be set when weekly timer activates (ON/OFF).SW2In case of Remote control mode, use

Strany 100 - Apply putty here

8-4. Mode SettingAccording to the function of each system controller, setSW1 as shown in Fig. 8-5.(1) Central control/Remote control modeCentral contr

Strany 101 - ADDITIONAL REFRIGERANT CHARGE

Part Name FigureQ’ty RemarksFull-scale installation diagram 1Flare insulator 2Washer 8Insulating tape 1Hose band2Packing 1Drain insulator 1Drain hose1

Strany 102

SC908-5. How to Perform Zone RegistrationTo operate the system controller properly, zone registration is required after finishing the test run (and af

Strany 103

SC(a) Zone registration using the remote controller(RCS-SH80UG)(Determination of central address)In this case, after confirming which indoor unit isco

Strany 104 - 11. TEST RUN

SC92(b) Zone registration using the system controller(SHA-KC64UG)In this case, you set all central addresses bythe system controller at once manually.

Strany 105

SC93(c) Automatic zone registration using the systemcontroller (SHA-KC64UG)(1) Press the and buttons at the sametime for more than 4 seconds. and C

Strany 106 - Outdoor unit control PCB

SC94How to check for overlapping of central address Nos.(1) Press the and buttons at the sametime for more than 4 seconds. and CODE No. C1 will fl

Strany 107

SC95Assign indoor unit addresses to the desired positions (central addresses)manually.2.1.For group control, only the main indoor unit should be assig

Strany 108 - Fig. 11-5

SC968-6. Connection with Other EquipmentON/OFFtupni latigiDAlarmOutput commonCPEVAWG#16ALL ON (+)CXTXALL OFF (+)Input commonCOM+24CPEVAWG#16emaNslanim

Strany 109

979. HOW TO PROCESS TUBINGThe liquid tubing side is connected by a flare nut, andthe gas tubing side is connected by brazing.9-1. Connecting the Ref

Strany 110

98Fig. 9-7 When removing the flare nuts from the tubingconnections, or when tightening them afterconnecting the tubing, be sure to use 2 monkeywrench

Strany 111

99Fig. 9-10Fig. 9-9Fig. 9-8Fig. 9-11 Do not use a spanner to tighten the valve stem caps.Doing so may damage the valves. Depending on the installati

Komentáře k této Příručce

Žádné komentáře