Sanyo POA-MD13NET2 Uživatelský manuál stáhnout pdf (Strana 52)

Chapter 4 Controlling the Projector

Load a control set

Select your desired set number with the pull-down menu button of the Load Setting

No. and then press the Set button. The setting values of the selected set number are

applied to the current settings.

Example of setting

✐ If the contents of the saved set are not match for the slot equipped on the projector, the

invalid alert message may be displayed. For example, the message “Invalid setting for

SLOT1” will be displayed in the following case.

Example: In case of after setting the DVI computer input for SLOT1 and then it was changed

to video input board.

1 2 ... 47 48 49 50 51 52 53 54 55 56 57 ... 91 92

POA-MD13NET2 1
Compliance 2
Contents 3
Chapter 1 5
Preparation 5
Features 6
Internet 7
Intranet 7
Operating Environment 8
Computer 9
The limitation* 9
Expression/Abbreviation 10
Use of this manual 10
Trademark 10
Chapter 2 11
Installation 11
Flow of installation 12
Caution 13
2 Remove 2 screws on a board 14
1 Turn the Mains switch off 14
(10Base-T, 100Base-TX) 15
UTP straight cable 15
Projector 15
Mains Switch 15
1 Selection of network menu 16
3 Restart the Network board 17
Network PIN code setting 18
10-key pallet 19
Network configuration (Type2) 20
Password 22
Network Board 23
Chapter 2 Installation 24
Chapter 3 25
Basic Setting and Operation 25
1 Enter the IP address 26
Display of main setting page 27
Initial Settings 29
2 Password Setting 30
3 Date/Time Setting 30
Network Configuration 31
E-mail Setting 32
E-Mail Setting 33
Chapter 4 35
Controlling the Projector 35
Power on/off the projector 36
Check the status of projector 37
Control the projector 38
PC Adjustment 39
Load a Set 40
Save a Set 40
System Adjustment 41
Image Adjustment 42
Save a image adjustment value 43
Load a image mode 43
Sound Adjustment 44
Screen Adjustment 44
Control the Projector 45
About Lamp Counter reset 46
1 Set a day or date 48
2 Set a time 48
4 Register an event 48
Getting the current time 49
Cancel the timer 49
1 Adjust and set the controls 51
2 Select the Save page 51
3 Name the current setting 51
4 Save the current setting 51
Load a control set 52
Control the projector’s menu 53
Make a memo 54
Chapter 5 55
Multi-Control 56
OWNER’S MANUAL 57
IP address 57
Projector name 57
Chapter 6 61
Use of Serial Port 61
Serial Port setting 62
RS-232C serial cable 64
Use of Telnet 66
Chapter 6 Use of Serial Port 68
* Use the IP address 68
Command list table 68
Chapter 7 69
Appendix:A 69
Examples of Connection 70
Examples of connection 71
To another network 71
Web browser setting 72
Examples: OS/Browsers 73
Proxy setting 74
Netscape Navigator v.7.0 75
JavaScript Setting 75
Mac OS 8.6 77
Netscape Navigator v.4.7 79
Product specification 81
Port Specification 82
Appendix:B 83
Installation/Access 84
Chapter 7 Appendix 86
IDRMD (built in KJ5AL) (b) 92

Komentáře k této Příručce

Žádné komentáře

Sanyo POA-MD13NET2 Uživatelský manuál Strana 52

Komentáře k této Příručce

Související produkty a manuály pro Projektory Sanyo POA-MD13NET2